 LM-1 Data log, MPS/AFR |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
  |
| rfinegan |
 Feb 13 2026, 01:24 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,176 Joined: 8-February 13 From: NC Member No.: 15,499 Region Association: MidAtlantic Region 
 |
I wired up the O2 and the LM-1 with a new Tach channel (I need a TPS for throttle position/load next)
I think this a a cruise speed , with a little more throttle in near the end. The full stop (3/4 to wot)seems to be about 12.1 or so ( I am liking that ok) NOT SEEN ON THIS SESSION MPS looks lean on cruise/ part load Head temp gets hot on light cruise about 60 MPH This tool seems to have a lot of features for the $$$ and still works well for being so OLD! Maybe some decel/over run here too on the graph, I need t make notes on the recordings, not EZ for 1 person that is the driver.  |
   |
 
|
| rfinegan |
Feb 13 2026, 01:30 PM
Post
#2
|
|
Senior Member Group: Members Posts: 1,176 Joined: 8-February 13 From: NC Member No.: 15,499 Region Association: MidAtlantic Region
|
or maybe use a old school vac gauge. :think
|
|
|
|
| rfinegan |
Feb 13 2026, 01:40 PM
Post
#3
|
|
Senior Member Group: Members Posts: 1,176 Joined: 8-February 13 From: NC Member No.: 15,499 Region Association: MidAtlantic Region
|
QUOTE(rfinegan @ Feb 13 2026, 02:30 PM)  or maybe use a old school vac gauge. :think A little tweek to the part load (middle Screw CCM Loosen) 1/8 turn to start? I just need to get her road worthy, While I work on my Clewette/ Electromotive TechGT 2056 |
|
|
|
| Ninja |
Feb 13 2026, 03:52 PM
Post
#4
|
|
Member Group: Members Posts: 133 Joined: 25-September 25 From: Granbury Texas Member No.: 29,004 Region Association: Southwest Region |
15.8 would bug me. I'd prefer 13.8-14.5 cruise and I'd want to know if 13.8 reduced cylinder heads temps versus 14.5.
3/4 throttle I'd want 12.5 or lower, once again I'd be looking at temp data here too. In my book 16 is "lean burn" beginning. On a water-cooled engine I'd want port injectors, modern digital FI, COP, and knock sensors. I would not be looking for power here, just fuel economy. I wouldn't run 16-1 on anything built in the 70s without fully updating everything and I'd still be more conservative and lean towards the rich side of things. |
|
|
|
| Ishley |
Feb 13 2026, 03:56 PM
Post
#5
|
|
Member Group: Members Posts: 316 Joined: 4-October 21 From: Clarendon Hills Il Member No.: 25,957 Region Association: Upper MidWest
|
I integrate O2 data that I capture on my PC with 123+ Distributor data captured on my phone simultaneously . You have to have the blue tooth version of the 123. Using time stamps form each source I can connect the data. I chart it and can see where I go lean and look at the other variables for why... and can make tweeks to the MPS from there.
Just another option to fill in the picture using data. |
|
|
|
| brant |
Feb 13 2026, 04:12 PM
Post
#6
|
|
914 Wizard Group: Members Posts: 12,137 Joined: 30-December 02 From: Colorado Member No.: 47 Region Association: Rocky Mountains 
|
Set your redline mixture for 13 or 13.5
Then mid range Too lean right now. |
 |
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 15th February 2026 - 07:04 AM |
Invision Power Board
v9.1.4 © 2026 IPS, Inc.